Voit 50 Fathom

Dedicated to the discussion of vintage diving methods and equipment available prior to 1970. This forum section is limited to the diving without modern BCDs or use of an Octopus.

Moderators: simonbeans, captain

Forum rules
Discussion of diving methods and equipment available prior to the development of BCDs beyond the horse collar. This forum is dedicated to the pre-1970 diving.
User avatar
Drado
Master Diver
 
Posts: 617
Joined: Mon Feb 07, 2011 6:11 am
Location: Manila, Philippines

Re: Voit 50 Fathom

Mon Apr 30, 2012 5:34 pm

What did you do with the original cans?
_______________________________
Ed

ImageImage

User avatar
Creed
Master Diver
 
Posts: 395
Joined: Mon Nov 07, 2005 12:10 pm
Location: San Ramon, CA

Re: Voit 50 Fathom

Mon Apr 30, 2012 6:03 pm

I still have them. Not sure if the can change will be permanent.
"Haul the sheet in as we ride on the wind that our
forefathers harnessed before us
Hear the bells ring as the tide rigging sings.
It's a son of a gun of a chorus" - Jimmy Buffet

User avatar
usddude
Master Diver
 
Posts: 317
Joined: Wed Jan 30, 2008 2:17 am
Location: Tennessee

Re: Voit 50 Fathom

Mon Apr 30, 2012 6:49 pm

That bottom can is worth a bit of dough. What about the extra pin hole in the top can? Maybe a different body at one time?

User avatar
Creed
Master Diver
 
Posts: 395
Joined: Mon Nov 07, 2005 12:10 pm
Location: San Ramon, CA

Re: Voit 50 Fathom

Mon Apr 30, 2012 7:14 pm

usddude wrote:That bottom can is worth a bit of dough. What about the extra pin hole in the top can? Maybe a different body at one time?

Not sure. The guy I bought it from didn't seem to know anything about it. I assumed that it was a factory hole, since it is chromed on the inside as well.
"Haul the sheet in as we ride on the wind that our
forefathers harnessed before us
Hear the bells ring as the tide rigging sings.
It's a son of a gun of a chorus" - Jimmy Buffet

User avatar
Greg Barlow
VDH Moderator
 
Posts: 445
Joined: Wed Jul 20, 2005 1:26 pm
Location: SW Ohio

Re: Voit 50 Fathom

Wed May 02, 2012 9:14 pm

usddude wrote:That bottom can is worth a bit of dough. What about the extra pin hole in the top can? Maybe a different body at one time?


I have rebuilt a significant number of 50 Fathom regs, and as far as I remember, they all had two holes. By having two holes, the can could be used for various single stage designs.

Greg
Greg Barlow
PADI Assistant Instructor
TDI Adv. EAN
TDI Decompression Procedures
IANTD Full Cave
NSS/CDS Full Cave

User avatar
Bronze06
Master Diver
 
Posts: 472
Joined: Tue Jul 01, 2014 5:33 am
Location: Tabuk, Saudi Arabia

Re: Voit 50 Fathom

Wed Apr 19, 2017 12:04 pm

Yup, that's right, a Voit 50 Fathom VCR-2, 1961 in the chrome. Do we have any source for seat and disk assembly (part 14) out there as well as micro-sized phenolic gaskets (part 11) for the seat? This is a new dingus for me. :?:


Chrome is slightly marred but good. Very shiny in the light.
20170419_183442.jpg


Interior is in good shape. The oft remarked factory "double holed" can.
20170419_183502.jpg



As you can see, our old friend at Professional Scuba Repair had this one in the shop. Most likely the last time it ever got serviced.

20170419_183527.jpg
You do not have the required permissions to view the files attached to this post.
"Where'd ya get that ol' thang, don't cha' know them thare things ill kill ya!"

Live From the Red Sea,

Russ

User avatar
Bryan
Plank Owner
 
Posts: 4709
Joined: Fri Jun 24, 2005 11:40 am
Location: Wesley Chapel Florida

Re: Voit 50 Fathom

Wed Apr 19, 2017 12:21 pm

New seats are difficult to come by new but I do have a few. I have a nylon gasket that will replace the phenolic as it was too expensive to re-make them in the original material considering the low demand for the part.
Doing it right should include some common sense, not just blindly following specs and instructions. .Gary D, AWAP on SB

User avatar
Bronze06
Master Diver
 
Posts: 472
Joined: Tue Jul 01, 2014 5:33 am
Location: Tabuk, Saudi Arabia

Re: Voit 50 Fathom

Wed Apr 19, 2017 12:45 pm

Bryan wrote:New seats are difficult to come by new but I do have a few. I have a nylon gasket that will replace the phenolic as it was too expensive to re-make them in the original material considering the low demand for the part.


Bryan, E-mail sent. Right now the disk and seat assembly is holding air. I am using a 008 oring that is approximately the same diameter as the phenolic gaskets.Granted it is a wee bit thicker, but is under compression two ways. This reg only had the one gasket and it should have two. That said, it is holding air, but I would like to have a disk and seat assembly as a spare for this baby and get a nylon gasket to fill the bill for the "Seat" seal. Thanks for the quick reply.

PS: Is this a "Sea Hunt Forever" certifiable reg?????
"Where'd ya get that ol' thang, don't cha' know them thare things ill kill ya!"

Live From the Red Sea,

Russ

User avatar
Bronze06
Master Diver
 
Posts: 472
Joined: Tue Jul 01, 2014 5:33 am
Location: Tabuk, Saudi Arabia

Re: Voit 50 Fathom

Fri Apr 28, 2017 5:13 pm

As a temporary fix, I have rebuilt a 1962 "Polaris" up stream body and guts that I will use in the 1961 50 Fathom. The original 1961down stream held only for awhile after re-build at 2600 psi, but the disk assembly (seat) lost its ability to hold back the tide at 2800psi and of course I have yet to get a new disk assembly. It's a good and safe fix for now and breathes and holds well at 3200 psi. I am eventually getting a NOS disk assembly from Bryan when I order some more parts. No rush. Sorry purists!!! :oops: :oops: :oops: Not to worry, my 1959 Blue can Fathom 50 is still kicking with its original guts.

I am guessing that Voit only used the down stream mechanism for a short run ( 1959 to 1961) due to the inherent possiblity of: overpressure causing loss of air through the disk assembly as well as lawsuits or am I mistaken.
"Where'd ya get that ol' thang, don't cha' know them thare things ill kill ya!"

Live From the Red Sea,

Russ

Previous
Return to Classic Vintage Diving

Who is online

Users browsing this forum: No registered users and 1 guest